Bob Lowry on When Pool pH Crashes
- 19m
- Transcript
Summary
Written by a model from the transcript; not yet reviewed.
In this episode, the host sits down with chemistry expert Bob Lowry to discuss the causes, effects, and management of low pH in swimming pools and hot tubs. While high pH gets more attention in the industry, the guest explains how corrosive low-pH water etches plaster, damages metallic equipment, and leaches hidden metals that eventually cause severe staining. They examine why vinyl and fiberglass pools are particularly prone to dropping in pH due to a lack of dissolved calcium and alkalinity, and how even a single drop of muriatic acid can strip color from vinyl surfaces. The conversation also debunks common chemical myths, such as using baking soda to raise pH, and provides practical methods for balancing water using borax, soda ash, and aeration.
- Run a test for iron and copper every couple of months to catch dissolved metals before they cause pool staining. 4:03
- Avoid using baking soda to raise pH because its maximum solution pH is 8.3 and it gasses off below a pH of 5. 10:53
- Use soda ash when you need to raise both pH and alkalinity simultaneously since it has a high pH of 13. 11:16
- Combine baking soda to reach the desired alkalinity with aeration to safely raise the pH without overshooting. 14:33
Chapters
- 0:00Podcast Intro and Sponsorships
Hosts introduce the episode and list sponsors Hasa and Skimmer.
- 1:05Meet Bob Lowry and Episode Focus
Host welcomes chemistry expert Bob Lowry and outlines the discussion on low pool pH.
- 2:22Low pH Effects on Plaster Pools
Bob explains how low pH causes corrosion and etching in plaster pools and equipment.
- 4:29Testing for Copper and Iron
Bob stresses the importance of testing for metals to prevent staining and corrosion.
- 5:22Low pH Impact on Vinyl and Fiberglass Pools
Discussion of why vinyl/fiberglass pools drift to lower pH and the damage it causes.
- 14:26Soda Ash and Bi‑Carbonate Use
Explanation of when to use soda ash versus bicarbonate to adjust pH and alkalinity.
- 17:14Cyanic Acid and Chlorine Efficacy
Bob discusses how cyanate levels affect chlorine’s killing power at different pH levels.
- 18:50Episode Wrap‑Up and Resources
Host summarizes key points, directs listeners to additional podcasts and coaching programs, and signs off.
Highlights
- 2:22
Corrosive Effects of Low pHinsight
Low pH makes water aggressive, etching plaster and dissolving metallic components in the pool system. Once dissolved metals reach their saturation point, they precipitate and cause severe staining.
- 6:47
Acid Damage on Vinyl Linersstory
The guest shares an anecdote from his time at Leslie's where pouring liquid chlorine on vinyl did nothing, but a single drop of muriatic acid immediately stripped the color and created a white spot.
- 10:39
Why Bicarbonate Fails at Low pHinsight
Baking soda cannot effectively raise pH because its strongest solution only reaches 8.3. Furthermore, if the pH drops below 5, adding bicarbonate causes it to gas off as CO2 without raising the pH at all.
- 13:35
Borates and Total Alkalinity Readingsdata
Adding borates to a pool affects the total alkalinity reading. At a pH of 7.5, 50 parts per million of borate shifts the reading by 6 to 7 parts per million, and the impact increases at higher pH levels.
- 14:26
Using Aeration to Raise pHstrategy
To balance a pool with low pH and low alkalinity, add baking soda to hit the target alkalinity and then use an aerator or blower to drive the pH up to 7.5 naturally.
- 15:46
Chlorine Effectiveness and pHinsight
The traditional belief that high pH drastically reduces chlorine killing power is largely mitigated by cyanic acid concentration. However, maintaining pH below 7.8 remains critical to prevent bather skin and eye irritation.
Quotes
“When the pH is low, the water gets to be what we say is corrosive or aggressive.”
Unnamed speaker · 2:22 “Low pH actually affects the vinyl more than chlorine level does.”
Unnamed speaker · 6:19 “If you ever get the pH below about five, you can't put bi carb in anyway.”
Unnamed speaker · 11:56 “The borax product, in my opinion, is a great way to do it if it's really low and you're wanting to raise the pH.”
Unnamed speaker · 10:13 “The killing power is not going to be that much different, but you need to have enough chlorine in there to prevent the algae.”
Unnamed speaker · 16:44
Sponsored segments
- Hasa 0:00–0:25
- Skimmer 0:26–0:49
- Leslie's 1:32–1:51
- UPA 7:07–7:48
- Hasa 19:08–19:12
- Skimmer 19:20–19:28
About this episode
Low pH is one of the most expensive “quiet problems” in pool care, because it doesn’t just make water feel off, it can actively eat your pool. We sit down with legendary pool chemistry expert Bob Lowry and walk through what aggressive, corrosive water really means in the real world: plaster that starts to etch and turn rough, metal components that dissolve into the water, and the frustrating moment when invisible copper or iron finally hits a saturation point and shows up as stains. If you’ve...
Transcript
3,184 words · 3 speakers
Topics
- chlorine
- bi carb
- cyanic acid
- soda ash
- baking soda
- borax
- chloramines
- diclor
- Costco
- Color Q Pro 9 2X
Page updated · transcript and summary are machine-generated