Skip to content

A Pool Service Checklist For When The Water Looks Dead

The Pool Guy Podcast Show

17m
Transcript

Original podcast

Where to listen

Summary

Written by a model from the transcript; not yet reviewed.

When arriving at a service stop to find a pool with dead-looking water, surface debris, and a stopped cleaner, a systematic troubleshooting checklist helps identify the root cause. A speaker with 35 years of industry experience breaks down the step-by-step process of diagnosing equipment failures, from simple user errors like deactivated variable-speed pumps to faulty timers, burnt-out capacitors, clogged impellers, and dirty filters. By working through each component systematically, service professionals can quickly pinpoint why a pool stopped circulating and restore it to proper operation.

  • Inform customers that pressing the start-stop button on a standalone variable-speed pump completely takes it out of its weekly programming cycle. 2:55
  • Reset a glitching Jandy AquaLink system by turning off the breakers for thirty seconds to restore normal programming. 4:12
  • Check for a low filter PSI reading around five to seven to determine if debris is jamming the pump impeller. 10:21
  • Inspect single-cartridge filters for complete failure when noticing a major drop-off in skimmer suction and flow. 14:09

Chapters

  1. 0:00
    Podcast Sponsorship Announcements

    Hosts introduce the episode’s sponsors, Hasa and Skimmer, and highlight their products and offers.

  2. 1:05
    Host Introduction and Episode Overview

    The host welcomes listeners and outlines the checklist for diagnosing a dead‑looking pool.

  3. 2:24
    Pump Activation and Timer Troubleshooting

    Steps to verify the pump is on, including checking timers, VS pumps, and automatic systems.

  4. 7:06
    Relay and Capacitor Diagnostics

    How to identify bad relays, capacitors, and motor failures in automatic panels.

  5. 12:34
    Filter Performance and PSI Checks

    Assessing filter pressure, cleaning procedures, and when to backwash or replace cartridges.

  6. 14:22
    Cleaner, Suction, and Side‑Port Issues

    Examining automatic cleaners, side‑port vac locks, and suction leaks that affect water quality.

  7. 15:42
    Runtime and Schedule Verification

    Ensuring the pool runs for the intended hours and identifying misconfigured timers.

  8. 17:09
    Closing Remarks and Resources

    The host wraps up, directs listeners to coaching programs, and repeats sponsor messages.

Highlights

  • 2:55

    Variable Speed Pump Overrideinsight

    Customers often press the start-stop button on standalone variable-speed pumps to silence noise during family gatherings, which takes the pump completely out of its weekly schedule.

  • 4:12

    Jandy AquaLink Glitch Resetstrategy

    Regular cycles on Jandy AquaLink systems can sometimes fail to start on time; turning off the system breakers for 30 seconds usually resets the programming successfully.

  • 5:20

    Mechanical Timer Trippersinsight

    Intermatic timers can fail when on-trippers wear out, slip out of place, or sit directly next to off-trippers, causing the pool to run for only a few minutes.

  • 6:00

    Automatic Panel Bad Relaysinsight

    Relays in Pentair and AquaLink automated panels can go bad, preventing the pump from turning on or causing it to run continuously 24/7.

  • 8:22

    Diagnosing Bad Capacitorsstrategy

    A pump that hums, clicks, or attempts to start before stopping usually indicates a failed capacitor that needs to be swapped out.

  • 10:21

    Low PSI Impeller Checkdata

    A filter PSI reading of five or six instead of the normal 20 indicates that debris is blocking the impeller behind the pump basket.

  • 14:22

    Vac-Lock Suction Shutoffinsight

    When suction hoses disconnect from a side port, the vac-lock device closes to prevent entrapment, which cuts off suction to the pump and degrades pool quality.

Quotes

  • “If the PSI is low, it's below 10, when it should be at 20 or 25, what I do is I'll turn off the system, I'll take the pump lid off, I'll take the pump basket out, and then I'll take a long flathead screwdriver.”
    Unnamed speaker · 11:18
  • “The AquaLink seem to be the system that does that.”
    Unnamed speaker · 4:33
  • “If you have a single cartridge filter, a lot of times, you're going to notice a pretty good drop-off in suction and in flow, and this is because that cartridge filter is no longer any good.”
    Unnamed speaker · 13:52
  • “Sometimes, the customer will reset the schedule on the automatic system, and it's not running as long as it's supposed to.”
    Unnamed speaker · 15:42
  • Hasa 0:00–0:24
  • Skimmer 0:27–0:49
  • Hasa 17:07–17:47

About this episode

You walk into the backyard and your stomach drops: the surface is covered in debris, there’s dust floating on top, and the cleaner looks like it gave up days ago. When a pool “isn’t working,” the fastest path to a fix is a calm, repeatable troubleshooting order, and that’s what I lay out here for pool service techs and anyone responsible for pool circulation and water clarity. I start at the controls because the easiest failures are often human ones. Standalone variable speed pumps can...

Transcript

0:00
17:50

3,407 words · 2 speakers

Topics

  • timer
  • relay
  • impeller
  • cartridge filter
  • capacitor
  • automatic system
  • inimatic timer
  • Pentair
  • Hayward
  • AquaLink

Page updated · transcript and summary are machine-generated